- Compact design.
- Bellows specially designed for high durability.
- Non-rising adjustment knob.
- Lockable knob system.
Direct-acting Pressure Reducing Valves
Pressure reducing valve PRV25
The ADCA PRV25 is a series of direct acting pressure reducing valves designed for use on steam, compressed air, water and other gases and liquids. These regulators are suitable for reducing steam pressure at the point of use on laundry machines, dyeing, food industries, sterilizers, etc.
- Rising adjustment knob with lock nut.
- Top cap (adjustment screw with cover).
- Spring and dome load version.
- Gauge connection on body.
- Saturated steam, compressed air, water and other gases and liquids compatible with the construction
- PRV25/2S and PRV25/2SG – carbon steel.
- PRW25/2S – carbon steel, balanced soft sealing.
- PRV25i and PRV25iG – stainless steel.
- PRW25i – stainless steel, balanced soft sealing.
- Suffix G: soft sealed with PTFE/GR.
- 1/2" to 1"; DN 15 to DN 25.
- Female threaded ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 25.
- Flanged ASME B16.5 Class 150 or 300.
- Horizontal installation is recommended.
- A “Y” strainer should be installed upstream of the valve.
- See IMI – Installation and maintenance instructions.
Pressure reducing valve RP45 (EN)
The ADCA RP45 series pressure reducing valves are single seated, bellows sealed controllers that operate without auxiliary energy.
Designed for use with steam, compressed air, and other gases compatible with the construction.
These valves are particularly suitable for reducing steam pressure in all energy and process systems where pressures must be kept under control.
- Specially designed high durability bellows, providing pressure balancing and frictionless plug stem.
- Robust construction (fit-and-forget).
- Suitable for use with high pressure turndowns.
- Interchangeable actuators and adjustment springs.
- Soft sealing in PTFE/GR for use with steam.
- Soft sealing in nitrile rubber for use with air and gases.
- Low-noise flow divider.
- Sensing pipe on body.
- Steam, compressed air and other gases compatible with the construction.
- Limited use with liquids.
- Consult manufacturer before installing the valve with liquids.
- RP45G and RP45GT or N – SG iron.
- RP45S and RP45ST or N – carbon steel.
- RP45i and RP45iT or N – stainless steel (only available from DN 15 to DN 100).
- Suffix T: soft sealed with PTFE/GR.
- Suffix N: soft sealed with nitrile rubber.
- DN 15 to DN 150.
- RP45G – Flanged EN 1092-2 PN 16.
- RP45S and RP45i – Flanged EN 1092-1 PN 16 or PN 40.
- Standard PN 16 DN 65 flanges are supplied with 4 holes. 8 holes, according to EN 1092-1/-2 on request.
- A1, A10, A11, A12, A3, A4, B1, B3, B4 and C11 – carbon steel.
- A2, A21, B2 and B21 – SG iron or carbon steel.
- A1i, A10i, A11i, A12i, A2i, A21i, A3i and A4i – stainless steel.
- See IMI – Installation and maintenance instructions.
Pressure reducing valve RP45 (ASME)
The ADCA RP45 series pressure reducing valves are single seated, bellows sealed controllers that operate without auxiliary energy.
Designed for use with steam, compressed air, and other gases compatible with the construction.
These valves are particularly suitable for reducing steam pressure in all energy and process systems where pressures must be kept under control.
- Specially designed high durability bellows, providing pressure balancing and frictionless plug stem.
- Robust construction (fit-and-forget).
- Suitable for use with high pressure turndowns.
- Interchangeable actuators and adjustment springs.
- Soft sealing in PTFE/GR for use with steam.
- Soft sealing in nitrile rubber for use with air and gases.
- Low-noise flow divider.
- Sensing pipe on body.
- Steam, compressed air and other gases compatible with the construction.
- Limited use with liquids.
- Consult manufacturer before installing the valve with liquids.
- RP45S and RP45ST or N – carbon steel.
- Suffix T: soft sealed with PTFE/GR.
- Suffix N: soft sealed with nitrile rubber.
- 1/2" to 6".
- Flanged ASME B16.5 Class 150 or 300.
- A1, A10, A11, A12, A3, A4, B1, B3, B4 and C11 – carbon steel.
- A2, A21, B2 and B21 – SG iron or carbon steel.
- A1i, A10i, A11i, A12i, A2i, A21i, A3i and A4i – stainless steel.
- See IMI – Installation and maintenance instructions.
Pressure reducing valve RP45 (Threaded)
The ADCA RP45 series of pressure reducing valves are single seated, bellows sealed controllers that operate without auxiliary energy.
Designed for use with steam, compressed air, and other gases compatible with the construction.
These valves are particularly suitable for reducing steam pressure in all energy and process systems where pressures must be kept under control.
- Specially designed high durability bellows, providing pressure balancing and frictionless plug stem.
- Robust construction (fit-and-forget).
- Suitable for use with high pressure turndowns.
- Interchangeable actuators and adjustment springs.
- Soft sealing in PTFE/GR for use with steam.
- Soft sealing in nitrile rubber for use with air and gases.
- Sensing pipe on body.
- Steam, compressed air and other gases compatible with the construction.
- Limited use with liquids.
- Consult manufacturer before installing the valve with liquids.
- RP45S and RP45ST or N – carbon steel.
- RP45i and RP45iT or N – stainless steel.
- Suffix T: soft sealed with PTFE/GR.
- Suffix N: soft sealed with nitrile rubber.
- 1/2" to 2".
- Female threaded ISO 7 Rp or NPT.
- A1, A10, A11, A12, A3, A4 – carbon steel.
- A2, A21, B2 and B21 – SG iron or carbon steel.
- A1i, A10i, A11i, A12i, A2i, A21i, A3i and A4i – stainless steel.
- See IMI – Installation and maintenance instructions.
Pressure reducing valve RPW45B (EN)
The ADCA RPW45B series pressure reducing valves are single seated, diaphragm sensing proportional controllers that operate without auxiliary energy.
Designed for use with water, compressed air and other liquids and gases compatible with the construction.
- Pressure balancing through robust piston design.
- Soft sealing to meet tight shut-off requirements.
- Robust construction (fit-and-forget).
- Interchangeable actuators and adjustment springs.
- Low-noise flow divider.
- Sensing pipe on body.
- Water, compressed air and other liquids or gases compatible with the construction.
- RPW45BG – SG iron.
- RPW45BS – carbon steel.
- RPW45Bi – stainless steel.
- DN 50 to DN 100.
- Flanged EN 1092-1 PN 16 or PN 40.
- Standard PN 16 DN 65 flanges are supplied with 4 holes. 8 holes, according to EN 1092-1/-2 on request.
- A1, A10, A12, A3 and A4 – carbon steel.
- A2 and A21 – SG iron or carbon steel.
- A1i, A10i, A12i, A2i, A21i, A3i and A4i – stainless steel.
- See IMI – Installation and maintenance instructions.
Diaphragm sensing pressure reducing valve P7
The ADCA P7 series pressure reducing valves are direct acting, spring loaded, diaphragm sensing balanced plug regulators designed for use with steam, nitrogen, compressed air, water and other gases and liquids compatible with the materials of construction.
Particularly suitable for general purpose applications where low flow and high temperatures are involved.
Also specifically recommended to operate as a pilot valve in combination with other pressure regulators
- Compact design.
- Robust stainless steel diaphragm.
- Precise milibar control.
- 1/4” gauge connection on body.
- Top cap (adjustment screw with cover).
- External sensing connection.
- Low pressure top.
- Dome loaded version.
- Bar stock stainless steel construction.
- Steam, compressed air and other gases compatible with the construction
- P7SS – stainless steel, diaphragm sensing.
- 1/4” and 3/8".
- Female threaded ISO 7 Rp or NPT.
- Ininstallation horizontal
- See IMI – Installation and maintenance instructions.
Diaphragm sensing pressure reducing valves P20D
The ADCA P20D is a series of direct acting, spring-loaded, diaphragm sensing and balanced plug pressure reducing valves.
These regulators are designed for use with compressed air, water and other gases and liquids compatible with the construction materials and valve design.
They are suitable for pressure reducing applications at the point of use in laundry and dyeing machines, food industries, sterilizers, etc.
- Compact design.
- Non-rising adjustment knob.
- Balanced valve plug.
- Completely machined from solid bar stock material.
- Ultrasonically cleaned.
- Leakage line connection.
- Gauge connection on body.
- Different soft valves for liquids and gases.
- Top cap (adjustment screw with cover).
- Degreased for oxygen application.
- Panel mounting.
- Self relieving.
- Compressed air, water and other gases and liquids compatible with the construction.
- P20D – stainless steel, diaphragm sensing.
- 1/4" to 1/2"; DN 15.
- Female threaded ISO 7 Rp, ISO 228 or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Horizontal or vertical installation.
- See IMI – Installation and maintenance instructions.
Piston sensing pressure reducing valves P20P
The ADCA P20P is a series of direct acting, spring loaded, piston sensing pressure reducing valves.
These regulators are designed for use with nitrogen, compressed air, water and other gases and liquids compatible with the materials of construction.
They are suitable for general purpose pressure reducing applications such as instrumentation systems and industrial equipment where small loads and high pressures are involved.
- Compact design.
- Machined from bar stock materials.
- Non-rising adjustment knob.
- Ultrasonically cleaned and degreased.
- Gauge connection on body.
- Different soft valves for liquids and gases.
- Top cap (adjustment screw with cover).
- Degreased for oxygen application.
- Leakage line connection.
- Panel mounting.
- Bottom mounting.
- Self relieving.
- Compressed air, water and other gases and liquids compatible with the construction.
- P20P – stainless steel, piston sensing, low flow.
- 1/4".
- Female threaded ISO 7 Rp, ISO 228 or NPT.
- In any position.
- See IMI – Installation and maintenance instructions.
Diaphragm sensing pressure reducing valves P20DS
The ADCA P20DS is a series of direct acting, spring loaded, diaphragm sensing balanced plug pressure reducing valves.
These regulators are particularly suitable for general purpose applications where low flow and high temperatures are involved and have been especially designed for use with steam.
- Compact design.
- Robust stainless steel diaphragm.
- Non-rising adjustment knob.
- Balanced valve plug.
- Completely machined from solid bar stock material.
- Leakage line connection.
- Gauge connection on body.
- Different soft valves for liquids and gases.
- Top cap (adjustment screw with cover).
- Degreased for oxygen application.
- Connection for external sensing line.
- Panel mounting.
- Steam, compressed air and other gases compatible with the construction.
- P20DS – stainless steel, diaphragm sensing
- 1/4" to 1/2"; DN 15.
- Female threaded ISO 7 Rp, ISO 228 or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Horizontal or vertical installation.
- See IMI – Installation and maintenance instructions.
Diaphragm sensing pressure reducing valves PRV30SS (1/2" to 1" – DN 15 to DN 25)
The ADCA PRV30SS is a series of direct acting, spring-loaded, diaphragm sensing and balanced plug pressure reducing valves.
These regulators are designed for use with compressed air, water and other gases and liquids compatible with the construction materials and valve design.
They are suitable for pressure reducing applications at the point of use in laundry and dyeing machines, food industries, sterilizers, etc.
- Compact design.
- Built-in strainer.
- Balanced valve plug.
- Full stainless steel construction.
- Various sealing options to meet compatibility requirements.
- Self relieving.
- Gauge connection on body.
- Different soft valves for liquids and gases.
- Dome-loaded version.
- Top cap (adjustment screw with cover).
- Degreased for oxygen application.
- Compressed air, water and other gases and liquids compatible with the construction.
- PRV30SS – stainless steel, diaphragm sensing
- 1/2" to 1"; DN 15 to DN 25.
- Female threaded ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Horizontal installation.
- See IMI – Installation and maintenance instructions.
Diaphragm sensing pressure reducing valves PRV30SS (1" to 2" – DN 25 to DN 50)
The ADCA PRV30SS is a series of direct acting, spring-loaded, diaphragm sensing and balanced plug pressure reducing valves.
These regulators are designed for use with compressed air, water and other gases and liquids compatible with the construction materials and valve design.
They are suitable for pressure reducing applications at the point of use in laundry and dyeing machines, food industries, sterilizers, etc.
- Compact design.
- Built-in strainer.
- Balanced valve plug.
- Full stainless steel construction.
- Various sealing options to meet compatibility requirements.
- Self relieving.
- Gauge connection on body.
- Different soft valves for liquids and gases.
- Dome-loaded version.
- Top cap (adjustment screw with cover).
- Degreased for oxygen application.
- Compressed air, water and other gases and liquids compatible with the construction.
- PRV30SS – stainless steel, diaphragm sensing
- 1" to 2"; DN 25 to DN 50
- Female threaded ISO 7 Rp or NPT (only available from 11/4" to 2").
- Flanged EN 1092-1 PN 40 (only available from DN 32 to DN 50) or PN 63.
- Flanged ASME B16.5 Class 150 or 300 (only available from 11/4" to 2") or Class 600.
- Horizontal installation.
- See IMI – Installation and maintenance instructions.
Piston sensing pressure reducing valves PRV31SS (1/2" to 1" – DN 15 to DN 25)
The ADCA PRV31SS is a series of direct acting, spring-loaded, piston sensing and balanced plug pressure reducing valves.
These regulators are designed for use with compressed air, water and other gases and liquids compatible with the construction materials and valve design.
They are suitable for pressure reducing applications at the point of use in laundry and dyeing machines, food industries, sterilizers, etc.
- Compact design.
- Built-in strainer.
- Balanced valve plug.
- Full stainless steel construction.
- Various sealing options to meet compatibility requirements.
- Self relieving.
- Gauge connection on body.
- Different soft valves for liquids and gases.
- Top cap (adjustment screw with cover).
- Degreased for oxygen application.
- Compressed air, water and other gases and liquids compatible with the construction.
- PRV31SS – stainless steel, piston sensing.
- 1/2" to 1"; DN 15 to DN 25
- Female threaded ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Horizontal installation.
- See IMI – Installation and maintenance instructions.
Piston sensing pressure reducing valves PRV31SS (1" to 2" – DN 25 to DN 50)
The ADCA PRV31SS is a series of direct acting, spring-loaded, piston sensing and balanced plug pressure reducing valves.
These regulators are designed for use with compressed air, water and other gases and liquids compatible with the construction materials and valve design.
They are suitable for pressure reducing applications at the point of use in laundry and dyeing machines, food industries, sterilizers, etc.
- Compact design.
- Built-in strainer.
- Balanced valve plug.
- Full stainless steel construction.
- Various sealing options to meet compatibility requirements.
- Self relieving.
- Gauge connection on body.
- Different soft valves for liquids and gases.
- Top cap (adjustment screw with cover).
- Degreased for oxygen application
Compressed air, water and other gases and liquids compatible with the construction.
PRV31SS – stainless steel, piston sensing.
1" to 2"; DN 25 to DN 50.
Female threaded ISO 7 Rp or NPT.
Flanged EN 1092-1 PN 40.
Flanged ASME B16.5 Class 150 or 300.
Horizontal installation.
See IMI – Installation and maintenance instructions.
Piston sensing pressure reducing valves PRV41SS
The ADCA PRV41SS is a series of direct acting, spring loaded, piston sensing pressure reducing valves.
These regulators are designed for use with nitrogen, compressed air, water and other gases and liquids compatible with the materials of construction.
They are suitable for general purpose pressure reducing applications such as instrumentation systems and industrial equipment where small loads and high pressures are involved.
- Compact design.
- Balanced valve plug.
- Completely machined from solid bar stock material.
- Gauge connection on body.
- Different soft valves for liquids and gases.
- Top cap (adjustment screw with cover).
- Degreased for oxygen application.
- Self relieving.
- Compressed air, water and other gases and liquids compatible with the construction.
- PRV41SS – stainless steel, piston sensing
- 1/4" to 3/4"; DN 15 and DN 20
- Female threaded ISO 7 Rp, ISO 228 or NPT.
- Flanged EN 1092-1 PN 40 to PN 250.
- Flanged ASME B16.5 Class 150, 300 or 600.
- Horizontal or vertical installation.
- See IMI – Installation and maintenance instructions.
Pilot operated Pressure Reducing Valves
Pilot operated pressuere reducing valve PRV57 DN15-100
ADCA PRV57 pilot operated pressure reducing valves are designed for use with steam, compressed air, nitrogen and other gases compatible with materials of construction.
PRV57 can be installed in pressure reducing stations in all industries, and provide sensitive and accurate control even when inlet pressure fluctuations or relevant flow variations occur.
- Accurate control of downstream pressures from 0.07 bar to 17 bar.
- Robust steel or stainless steel construction.
- Suitable for dead-end conditions.
- Guided piston and valve stem.
- Hardened stem tip.
- Soft plug
- Low pressure top end.
- Dome version.
- Bottom cap drain connection.
- Stellited plug and seat.
- Internal detection line.
- Saturated steam, compressed air and other gases compatible with construction (excluding oxygen).
- PRV57, PRV57E - steel steam versions.
- PRV57i, PRV57iE - stainless steel steam versions (only available from DN 15 to DN 50).
- PRV57G, PRV57GE - steel versions for compressed air and gases.
- PRV57Gi, PRV57GiE - stainless steel versions for compressed air and gases (only available from DN 15 to DN 50).
- Suffix E: version with solenoid valve for remote remote shut-off.
- PRS: All the above models are available with an optional lift valve pilot, e.g. PRS57G (see fig. 8).
- DN 15 to DN 100.
- Flange EN 1092-1 PN 16 or PN 40.
- Standard flanges PN 16 DN 65 are supplied with 4 orifices. 8 orifices, according to EN 1092-1, on request.
- Horizontal installation, see IMI -
- In steam applications, a Y-strainer, a moisture separator and a steam trap must be installed.
Pilot operated pressuere reducing valve PRV47 DN15-50
ADCA PRV47 pilot operated pressure reducing valves are designed for use with steam, compressed air, nitrogen and other gases compatible with materials of construction.
PRV47 can be installed in pressure reducing stations, in all industries, and provide sensitive and accurate control even when inlet pressure fluctuations or relevant flow variations occur.
- Accurate control of downstream pressures from 0.07 bar to 17 bar.
- Robust steel or stainless steel construction.
- Suitable for dead-end conditions.
- Guided piston and valve stem.
- Hardened plug.
- Soft sealing.
- Low pressure top.
- Dome version.
- Bottom cap drain connection.
- Stellited plug and seat.
- Internal sensing line.
- Saturated steam, compressed air and other gases (group 2) compatible with construction (except oxygen).
- PRV47, PRV47E - steel steam versions.
- PRV47i, PRV47iE - stainless steel steam versions (only available from DN 15 to DN 50).
- PRV47G, PRV47GE - steel versions for compressed air and gases.
- PRV47Gi, PRV47GiE - stainless steel versions for compressed air and gases.
- Suffix E: Version with solenoid valve for remote shut off.
- PRS: All above models are available with optional lift valve pilot, e.g. PRS57G (see fig. 8).
- 1/2" to 2"; DN 15 to DN 50.
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Socket weld (SW) ASME B16.11.
- Horizontal installation.
- See IMI - Installation and Maintenance Instructions.
- In steam applications, a "Y" strainer, moisture separator, moisture separator and steam trap upstream of the valve.
Blanketing
Tank blanketing regulators BKRI2
Tank blanketing valves are commonly used in tank storage systems to prevent and protect against explosions (avoiding flammable liquids being vented from the vessel), to control product contamination against external air that may fill the vapour space, to reduce evaporation losses (consequently, production losses), to reduce internal corrosion (caused by air and moisture) and to prevent vacuum condition.
The blanketing process consists in covering the stored medium, usually a liquid, with a gas (normally N2).
- Compact design.
- Non-rising adjustment knob.
- FDA / USP Class VI compliant seals.
- STANDAR SURFACE FINISH
- Internal movable parts and machined surfaces:
- ≤ 0,76 micron Ra – SF3.
- Other surfaces: as casted.
- Ultrasonic cleaning.
- Leakage line connection 1/4”.
- Gauge connection on body.
- External pulse line (recommended for low set
- pressures < 10 mbar or high flow).
- Dome-loaded version.
- Blanketing with vacuum.
- Top cap (adjustment screw with cover).
- ATEX version.
- Compressed air, nitrogen and other gases compatible with the construction.
- BKRI2 – low pressure regulator.
- DN 15 and DN 25.
- 5 to 10 mbar; 10 to 50 mbar; 20 to 200 mbar;
- 50 to 500 mbar; 5 to 4000 mbar (dome-loaded).
- Flanged EN 1092-1 PN 16.
- Vertical installation recommended, to allow drainage, or horizontal as close to the process as possible in order to prevent long pipe sections and flow restrictions.
- See IMI – Installation and maintenance instrucions.
Tank blanketing regulators BKVI2
Tank blanketing valves are commonly used in tank storage systems to prevent and protect against explosions (avoiding flammable liquids being vented from the vessel), to control product contamination against external air that may fill the vapour space, to reduce evaporation losses (consequently, production losses), to reduce internal corrosion (caused by air and moisture) and to prevent vacuum condition.
The blanketing process consists in covering the stored medium, usually a liquid, with a gas (normally N2).
- Compact design.
- Non-rising adjustment knob.
- FDA / USP Class VI compliant seals.
- STANDAR SURFACE FINISH
- Internal movable parts and machined surfaces:
- ≤ 0,76 micron Ra – SF3.
- Other surfaces: as casted.
Ultrasonic cleaning.
- Leakage line connection 1/4”.
- Gauge connection on body.
- External pulse line (recommended for low set
- pressures < 10 mbar or high flow).
- Dome-loaded version.
- Blanketing with vacuum.
- Top cap (adjustment screw with cover).
- ATEX version.
- Compressed air, nitrogen and other gases compatible with the construction.
- BKRI2 – low pressure regulator.
- DN 15 and DN 25.
- 5 to 10 mbar; 10 to 50 mbar; 20 to 200 mbar;
- 50 to 500 mbar; 5 to 4000 mbar (dome-loaded).
- Flanged EN 1092-1 PN 16.
- Vertical installation recommended, to allow drainage, or horizontal as close to the process as possible in order to prevent long pipe sections and flow restrictions.
- See IMI – Installation and maintenance instrucions.
Pressure Reducing Station
Pressure reducing valve RPW45B (EN)
ADCA RPW45B series pressure reducing valves are single seat diaphragm proportional controllers that operate without auxiliary power.
Designed for use with water, compressed air and other liquids and gases compatible with the construction.
- Pressure balanced due to robust piston design.
- Soft sealing to meet tight shut-off requirements.
- Robust (fit and forget) construction.
- Interchangeable actuators and adjusting springs.
- Silent flow divider.
- Sensor tube in body.
- Water, compressed air and other liquids or gases compatible with the construction.
- RPW45BG - SG iron.
- RPW45BS - carbon steel.
- RPW45Bi - stainless steel.
- DN 50 to DN 100.
- Flanges EN 1092-1 PN 16 or PN 40.
- Standard flanges PN 16 DN 65 are supplied with 4 holes. 8 holes, according to EN 1092-1/-2 on request. on request.
- A1, A10, A12, A3 and A4 - carbon steel.
- A2 and A21 - SG iron or carbon steel.
- A1i, A10i, A12i, A2i, A21i, A3i and A4i - stainless steel.
- See IMI - Installation and maintenance instructions.
Pressure Regulating Valves for water are gases applications
Pressure reducing valve in bronze flanged connections series 682
For protection of:
- Domestic water supply systems
- Commercial and industrial plants
Against excess supply pressure.
The pressure reducers are used to adjust the outlet pressure even having pressure variations upstream the valve in:
- Drinking water supply according to DIN 1988 standard
- Process water supply in industrial and building technology
- Fire-fighting equipment and sprinkler systems
- Shipbuilding industry and offshore plants
Bronze pressure reducing valve with broken connections series 681
For protection of:
- Domestic water supply systems
- Commercial and industrial plants
Against excess supply pressure.
The pressure reducers are used to adjust the outlet pressure even when there are pressure variations upstream of the valve in...
- Drinking water supply according to DIN 1988 standard
- Process water supply in industrial and building technology
Fire fighting equipment and sprinkler systems
Shipbuilding industry and offshore plants
Bronze pressure reducing valve with threaded connections series 683
For the protection of:
- Commercial and industrial plants against too high supply pressure.
The pressure reducing valves are used to adjust the outlet pressure even if there are pressure variations upstream of the valve in the plant....
- Compressed air supply plants
- Pneumatic control units
- Air-side pressurization plants
- Shipbuilding industry and offshore plants
Bronze pressure reducing valve threaded connections series 684
For the protection of:
- Commercial and industrial plants against too high supply pressure.
The pressure reducing valves are used to adjust the outlet pressure even if there are pressure variations upstream of the valve in the plant....
- Compressed air supply plants
- Pneumatic control units
- Air side pressure pressurization plants
- Shipbuilding industry and offshore plants
- Industrial gas plant construction
- PET blow molding machines
- Demolition plants
Pressure reducing valve stainless steel flanged connections SERIES 482
For protection of:
- Domestic water supply systems
- Commercial and industrial plants
Against excess supply pressure.
The pressure reducers are used to adjust the outlet pressure even when there are pressure variations upstream of the valve in...
- Drinking water supply according to DIN 1988 standard
- Process water supply in industrial and building technology
- Fire fighting equipment and sprinkler systems
- Shipbuilding industry and offshore plants
Pressure reducing valve in stainless steel threaded connections 481
For protection of:
- Domestic water supply systems
- Commercial and industrial plants
Against excess supply pressure.
The pressure reducers are used to adjust the outlet pressure even when there are pressure variations upstream of the valve in...
- Drinking water supply according to DIN 1988 standard
- Process water supply in industrial and building technology
- Fire fighting equipment and sprinkler systems
- Shipbuilding industry and offshore plants
Stainless steel pressure reducing valve threaded connections 484
For the protection of:
Commercial and industrial plants against too high supply pressure.
The pressure reducers are used to adjust the outlet pressure even when there are pressure variations upstream of the valve in...
Compressed air supply plants
Pneumatic control units
Air side pressure pressurization plants
Shipbuilding industry and offshore plants
Industrial gas plant construction
PET blow molding machines
Demolition plants