- Modulating discharge
- Condensate discharge near saturation temperature
- Various thermostats for different cooling temperatures (5º or 30ºC).
- Excellent air elimination.
- Works with moderately superheated steam.
- Built-in filter.
Air eliminators for steam pipelines
Thermostatic steam traps and air vents TH13A
The TH13A series deaerator and air eliminator is specifically designed for use on process equipment such as boiling kettles, sterilizers, food, chemical and laundry machinery. Its small size makes it ideal for use in a wide variety of equipment and applications as a steam deaerator.
- Saturated steam.
- TH13A - brass.
- 1/2".
- Female thread ISO 7 Rp.
- Vertical installation, angled connections.
- See IMI - Installation and maintenance instructions
Condensate eliminators for gases pipelines
Air and gas float traps DN15-20 FA16SS
The FA16SS is a very compact, small and lightweight float condensate remover specially designed for condensate drainage in compressed air lines and other compatible gases (Natural Gas, CO2, industrial gases, etc...) compatible with the materials of manufacture. Application in dryers, coolers, receivers, low points of line and other components in gas lines. Female threaded connections and vertical mounting.
- Corrosion resistant
- Replaceable internals
- Modulating discharge
- Unaffected by pressure changes or increases in purge flow rate.
- Compression fitting.
- Manual purge knob
- Compressed air and non-corrosive gases compatible with construction.
- FA16SS - stainless steel.
1/2" y 3/4".
- ISO 7 Rp or NPT female thread.
- Vertical inlet 1/2" or 3/4" (top to bottom).
- Vertical outlet 1/2
- Vertical installation. It must be installed absolutely vertical in the points of the installation where the condensate
- installation where condensate tends to accumulate.
- The drain must be channeled to a safe position.
Air and gas float traps FA21.1 (SG iron ; 1/2" to 1" – DN 15 to 25)
The FA21.1 is a series of fully automatic ball float traps specially designed for condensate drainage in compressed air and gas systems.
Typical applications include aftercoolers, separators and compressed air mains.
- Modulating discharge.
- Unaffected by sudden or wide load and pressure variations.
- Flow direction can be easily changed by repositioning the body in relation to the mechanism and cover.
- Metal to metal sealing.
- Equalizing (vent) and drain connections.
- BDV – Blowdown valve.
- AFZ – Anti-freeze device.
- FLL – Float lifting lever.
- Compressed air and other non corrosive gases compatible with the construction.
FA21.1-4,5 , 10 and 14 – SG iron.
- 1/2" to 1"; DN 15 to DN 25.
- Female threaded ISO 7 Rp or NPT.
- Flanged EN 1092-1/-2 PN 16.
- Flanged ASME B16.42/B16.5 Class 150.
- Inline horizontal or vertical installation.
- Angled horizontal or vertical installation.
- See IMI – Installation and maintenance instructions.
- Inline horizontal or vertical installation.
- Angled horizontal or vertical installation.
- See IMI – Installation and maintenance instructions.
MAX. ΔP:
- FA21.1-4,5 – 4,5 bar
- FA21.1-10 – 10 bar
- FA21.1-14 – 14 bar
Air and gas float traps FA25.1 (SG iron ; 1" - DN 25)
The FA25.1 is a series of fully automatic carbon steel eliminators specially designed for the drainage of condensate in compressed air and gas systems.
Typical applications include chillers, separators and main compressed air distribution lines.
- Modulating discharge.
- Unaffected by sudden or wide variations in load and pressure.
- Direction of flow can be easily changed by repositioning the body in relation to the mechanism and cover.
- Metal to metal sealing.
- Balance (vent) connection.
- BDV - Bleed valve.
- AFZ - Antifreeze device.
- FLL - Manual float actuation lever.
- Compressed air and other non-corrosive gases compatible with the construction.
- FA25.1-4,5 , 10 and 14 - SG Iron.
- 1"; DN 25.
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1/-2 PN 16.
- Flanged ASME B16.42/B16.5 Class 150.
- Horizontal or vertical installation in line.
- Horizontal or vertical installation at an angle.
- See IMI
MAX. AP
- FA25.1-4,5 – 4,5 bar
- FA25.1-10 – 10 bar
- FA25.1-14 – 14 bar
Air and gas float traps FA25.3 (iron SG ; 11/2" and 2" - DN 40 and 50)
The FA25.3 series is a range of fully automatic float eliminators specially designed for condensate drainage in compressed air and gas systems.
Typical applications include chillers, separators and main compressed air distribution lines.
- Modulating discharge.
- Unaffected by sudden variations in discharge flow or pressure.
- Direction of flow can be easily changed by repositioning the body in relation to the mechanism and cover
- Balance (vent) connection
- BDV - Bleed valve
- AFZ - Anti-freeze system
- FLL - Manual float actuation lever.
- Compressed air and other non-corrosive gases compatible with the construction
- FA25.3-4,5 , 10 and 14 - SG iron.
- 11/2" and 2"; DN 40 and DN 50
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-2 PN 16.
- Flanged ASME B16.42 Class 150.
- Horizontal or vertical installation.
MAX. AP
- FA25.3-4,5 – 4,5 bar
- FA25.3-10 – 10 bar
- FA25.3-14 – 14 bar
Air and gas float traps FA31.1 (Carbon steel ; 1/2" to 1" - DN 15 to 25)
The FA31.1 is a series of fully automatic carbon steel eliminators specially designed for condensate drainage in compressed air and gas systems.
Typical applications include chillers, separators and main compressed air distribution lines.
- Modulating discharge.
- Unaffected by sudden or wide variations in load and pressure.
- Direction of flow can be easily changed by repositioning the body relative to the mechanism and cover.
- Metal to metal sealing.
- Equalising (drain) and drain connections.
- BDV - Bleed valve.
- AFZ - Antifreeze device.
- FLL - Float lifting lever
- Compressed air and other non-corrosive gases compatible with the construction
- FA31.1-4,5 , 14, 10, 10, 21 and 32 - carbon steel
- 1/2" to 1"; DN 15 to DN 25.
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Socket weld (SW) ASME B16.11.
- Horizontal or vertical installation in line.
- Horizontal or vertical angled installation.
- See IMI – Instructions
MAX. AP
- FA31.1-4,5 – 4,5 bar
- FA31.1-10 – 10 bar
- FA31.1-14 – 14 bar
- FA31.1-21 – 21 bar
- FA31.1-32 – 32 bar
Air and gas float traps FA35.1 (Carbon steel 1"; DN 25)
The FA35.1 is a series of fully automatic carbon steel eliminators specially designed for condensate drainage in compressed air and gas systems.
Typical applications include chillers, separators and main compressed air distribution lines
- Modulating discharge.
- Unaffected by sudden or wide variations in load and pressure.
- Direction of flow can be easily changed by repositioning the body in relation to the mechanism and cover.
- Metal to metal sealing.
- Balance (vent) connection.
- BDV - Bleed valve.
- AFZ - Antifreeze device.
- FLL - Manual float actuation lever.
- Compressed air and other non-corrosive gases compatible with the construction
- FA35.1-4,5 , 10, 14, 14, 21 and 32 - carbon steel.
- 1"; DN 25.
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Socket weld (SW) ASME 16.11.
- Horizontal or vertical installation in line.
- Horizontal or vertical installation at an angle.
- See IMI - Installation and Maintenance Instructions.
MAX. AP
- FA35.1-4,5 – 4,5 bar
- FA35.1-10 – 10 bar
- FA35.1-14 – 14 bar
- FA35.1-21 – 21 bar
- FA35.1-32 – 32 bar
Air and gas float traps FA35.3 (Carbon Steel 11/2" - 2"; DN 40 - 50)
The FA35.3 series is a range of fully automatic float eliminators specially designed for condensate drainage in compressed air and gas systems.
Typical applications include chillers, separators and main compressed air distribution lines
- Modulating discharge.
- Unaffected by sudden variations in discharge flow or pressure. Direction of flow can be easily changed by repositioning the body in relation to the mechanism and cover.
- Balance connection (vent)
- BDV - Bleed valve
- AFZ - Anti-freeze system
- FLL - Manual float actuation lever.
- Compressed air and other non-corrosive gases compatible with the construction.
- FA35.3-4,5 , 10 , 14 , 14 , 21 and 32 - carbon steel.
- 11/2" to 2"; DN 40 to DN 50.
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Socket weld (SW) ASME B16.11.
- Horizontal or vertical installation.
AP. MAX:
- FA35.3-4,5 – 4,5 bar
- FA35.3-10 – 10 bar
- FA35.3-14 – 14 bar
- FA35.3-21 – 21 bar
- FA35.3-32 – 32 bar
Air and gas float traps FA41.1 (Stainless steel; 1/2" to 1" - DN 15 to 25)
The FA41.1 series is a range of stainless steel, fully automatic float eliminators specially designed for condensate drainage in compressed air and gas systems.
Typical applications include chillers, separators and main compressed air distribution lines.
- Modulating discharge.
- Unaffected by sudden variations in discharge flow or pressure.
- Flow direction can be easily changed by repositioning the body in relation to the mechanism and cover
- Balance connection (vent)
- BDV - Bleed valve
- AFZ - Anti-freeze system
- FLL - Manual float actuation lever
- Compressed air and other non-corrosive gases compatible with the construction.
- FA41.1-4,5 , 10, 14 , 21 and 32 - stainless steel
- 1/2" to 1"; DN 15 to DN 25.
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Socket weld (SW) ASME B16.11.
- Horizontal or vertical installation in line.
- Horizontal or vertical installation at an angle.
- See IMI - Installation and Maintenance Instructions.
AP MAX:
- FA41.1-4,5 – 4,5 bar
- FA41.1-10 – 10 bar
- FA41.1-14 – 14 bar
- FA41.1-21 – 21 bar
- FA41.1-32 – 32 bar
Air and gas float traps FA45.1 (Stainless steel 1"; DN 25)
The FA45.1 series is a range of stainless steel, fully automatic float eliminators specially designed for condensate drainage in compressed air and gas systems.
Typical applications include chillers, separators and main compressed air distribution lines.
- Modulating discharge.
- Unaffected by sudden variations in discharge flow or pressure.
- Flow direction can be easily changed by repositioning the body in relation to the mechanism and cover.
- Balance connection (vent)
- BDV - Bleed valve
- AFZ - Anti-freeze system
- FLL - Manual float actuation lever.
- Compressed air and other non-corrosive gases compatible with the construction
- FA45.1-4,5 , 10, 14, 14, 21 and 32 - stainless steel.
- 1"; DN 25
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Socket weld (SW) ASME 16.11.
- Horizontal or vertical installation in line.
- Horizontal or vertical installation at an angle.
- See IMI - Installation and Maintenance Instructions.
AP MAX:
- FA45.1-4,5 – 4,5 bar
- FA45.1-10 – 10 bar
- FA45.1-14 – 14 bar
- FA45.1-21 – 21 bar
- FA45.1-32 – 32 bar
Air and gas float traps GAS FA45.3 (Stainless steel 1"; DN 25)
The FA45.3 series is a range of fully automatic stainless steel float eliminators specially designed for condensate drainage in compressed air and gas systems.
Typical applications include chillers, separators and main compressed air distribution lines.
- Modulating discharge.
- Unaffected by sudden variations in discharge flow or pressure.
- Flow direction can be easily changed by repositioning the body in relation to the mechanism and cover.
- Balance connection (vent)
- BDV - Bleed valve
- AFZ - Anti-freeze system
- FLL - Manual float actuation lever.
- Compressed air and other non-corrosive gases compatible with the construction.
- FA45.1-4,5 , 10, 14, 14, 21 and 32 - stainless steel.
- 1"; DN 25.
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Socket weld (SW) ASME 16.11.
- Horizontal or vertical installation in line.
- Horizontal or vertical installation at an angle.
- See IMI - Installation and Maintenance Instructions
AP. MAX:
- FA45.3-4,5 – 4,5 bar
- FA45.3-10 – 10 bar
- FA45.3-14 – 14 bar
- FA45.3-21 – 21 bar
- FA45.3-32 – 32 bar
Compressed air automatic drain valves CAD
The automatic condensate drain valve for compressed air lines consists of a solid state timer coupled to a solenoid pilot valve. The CAD is specially designed for the removal of condensate from filters, separators, dryers, coolers, receivers, low points of lines and other components of compressed air distribution and consumer systems where effective removal of condensate and other contaminants is required. The drain interval and duration of the drain can be adjusted to suit the needs of the installation
- Easy and simple programming.
- Drain intervals and drain periods can be adjusted as required.
- Manual button for testing and checking operation.
- Easy to install
- Stainless steel valve body.
- Compressed air, oil, gases and liquids compatible with materials of construction
- CAD
- 3/8" y 1/2"
- Female thread ISO 7 Rp.
- In any position.
Air eliminators for liquid pipelines
Automatic air and gas vents for liquid systems AE16SS
The air eliminator AE16SS, made of stainless steel, removes air from the air conditioning systems, being suitable to work with all those fluids compatible with the materials of manufacture and whose specific weight is not less than 0.75 Kg/dm3. This automatic float eliminator can be used in combination with other air separation and elimination systems or directly installed at high points of the installation. Female threaded connections.
- Corrosion resistant wetted parts
- Replaceable internals
- Suffix "CK": Version with integrated check valve.
- Hot and cold water systems.
- AE16SSE - EPDM valve.
- AE16SSV - Viton valve.
- 1/2" y 3/4"
- Female threaded ISO 7 Rp or NPT.
- 1/2" or 3/4" vertical inlet.
- 1/2" vertical outlet.
- Vertical installation
- It must be installed absolutely vertically at points in the plant where air tends to accumulate. Discharge must be directed to a safe location.
- See IMI - Installation and Maintenance Instructions.
Automatic air and gas vents for liquid systems AE30SS
The AE30SS air eliminator, made of stainless steel, removes air from hot water and superheated water systems and is also suitable for working with all those fluids compatible with the materials of manufacture and whose specific weight is not less than 0.75 Kg/dm3. This automatic float eliminator can be used in combination with other air separation and elimination systems or directly installed at high points of the installation. Female threaded connections
- Corrosion resistant
- Replaceable internals
- Integrated check valve
- Cold, hot and superheated water systems.
- AE30SS - stainless steel.
- 1/2" y 3/4".
- Female thread ISO 7 Rp or NPT.
- Vertical inlet 1/2" or 3/4".
- Vertical outlet 1/2".
- Vertical installation. It must be installed absolutely vertically, in the points of the installation where air tends to accumulate. The drain must be channelled to a safe position.
- See IMI - Installation and maintenance instructions
Automatic air and gas vents for liquid systems AE31.2 (Carbon steel 1" x 1/2"; DN 25 x 15)
The AE31.2 range of automatic steam traps are designed to remove air or gases from water and other liquid systems, without requiring any external power source.
They are capable of handling large loads during start-up as well as smaller loads in continuous modulating operation with a single orifice.
These floating float type traps are manufactured from carbon steel, available with soft seating, and can be used in combination with other air removal and separation systems or directly applied at high points in distribution piping.
- Suitable for start-up and continuous operation with a single orifice.
- Allow for quick and easy in-line maintenance.
- Corrosion resistant internal parts.
- No balancing tube required.
- Metal to metal sealing.
- Threaded connection in the cover, closed with plug.
- HVV - Manual vent valve.
- Cold, hot and superheated water or other liquids compatible with the construction.
- AE31.2-6, 14, 21 and 32 - carbon steel.
- 1" x 1/2"; DN 25 x 15
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Socket weld (SW) ASME B16.11.
Automatic air and gas vents for liquid systems AE35.2 (Carbon steel 1” x 1/2”, 1” x 1”; DN 25 x 15, DN 25 x 25)
The AE35.2 range of automatic steam traps are designed to remove air or gases from water and other liquid systems, without requiring any external power source.
They are capable of handling large loads during start-up as well as smaller loads in continuous modulating operation with a single orifice.
These floating float type traps are manufactured from carbon steel, available with soft seating, and can be used in combination with other air removal and separation systems or directly applied at high points in distribution piping.
- Suitable for start-up and continuous operation with a single orifice.
- Allow for quick and easy in-line maintenance.
- Corrosion resistant internal parts.
- No balancing tube required.
- Metal to metal sealing.
- Threaded connection in the cover, closed with plug.
- HVV - Manual bleed valve
- Cold, hot and superheated water or other liquids compatible with the construction.
- AE35.2-6, 14, 21 and 32 - carbon steel.
- 1" x 1/2" and 1" x 1"; DN 25 x 15 and DN 25 x 25.
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Socket weld (SW) ASME 16.11.
- Vertical installation.
- It must be installed absolutely vertically at the points in the plant where the air tends to collect.
- See IMI – Installation and maintenance instructions.
MAX. AP:
- AE35.2-6 – 6 bar
- AE35.2-14 – 14 bar
- AE35.2-21 – 21 bar
- AE35.2-32 – 32 bar
Automatic air and gas vent for liquid systems AE37.2 (Carbon steel ; 11/2" x 1" and 2" x 1" – DN 40 x DN 25 and DN 50 x DN 25)
The AE37.2 range of automatic steam traps are designed to remove air or gases from water and other liquid systems, without requiring any external power source.
They are capable of handling large loads during start-up as well as smaller loads in continuous, modulating operation with a single orifice.
These floating float type traps are manufactured from carbon steel, available with soft seating, and can be used in combination with other air removal and separation systems or directly applied at high points in distribution piping
- Suitable for start-up and continuous operation with a single orifice.
- Allow for quick and easy in-line maintenance.
- Corrosion resistant internal parts.
- No balancing tube required.
- Various soft sealing options
- Cold, hot and superheated water or other liquids compatible with construction.
- AE37.2-10, 20 and 32 - carbon steel.
- 11/2" x 1" and 2" x 1"; DN 40 x DN 25 and DN 50 x DN 25.
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Socket weld (SW) ASME 16.11.
- Vertical in-line installation.
- It must be installed absolutely vertically at the points in the plant where the air tends to collect.
- See IMI – Installation and maintenance instructions.
MAX. AP:
- AE37.2-10 – 10 bar
- AE37.2-20 – 20 bar
- AE37.2-32 – 32 bar
Automatic air and gas vents for liquid systems AE39.2 (Carbon steel ; 21/2" x 11/2" and 3" x 11/2" – DN 65 x DN 40 and DN 80 x DN 40)
The AE39.2 range of automatic steam traps are designed to remove air or gases from water and other liquid systems, without requiring any external power source.
They are capable of handling large loads during start-up as well as smaller loads in continuous, modulating operation with a single orifice.
These floating float type traps are manufactured from carbon steel, available with soft seating, and can be used in combination with other air removal and separation systems or directly applied at high points in distribution piping.
- Suitable for start-up and continuous operation with a single orifice.
- Allow for quick and easy in-line maintenance.
- Corrosion resistant internal parts.
- No balancing tube required.
- Various soft sealing options.
- Cold, hot and superheated water or other liquids compatible with construction
- AE39.2-5, 10, 20, 20, 28 and 32 - carbon steel.
- 21/2" x 11/2" and 3" x 11/2"; DN 65 x DN 40 and DN 80 x DN 40.
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Socket weld (SW) ASME 16.11.
- Vertical in-line installation.
- It must be installed absolutely vertical at the points of the
- Installation should be installed absolutely vertical where air tends to accumulate.
- See IMI - Installation and Maintenance Instructions
MAX.AP:
- AE39.2-5 – 5 bar
- AE39.2-10 – 10 bar
- AE39.2-20 – 20 bar
- AE39.2-28 – 28 bar
- AE39.2-32 – 32 bar
Automatic air and gas vents for liquid systems AE41.2 (Stainless steel 1” x 1/2”; DN 25 x 15)
The AE41.2 range of automatic air vents are designed to remove air or gases from water and other liquid systems, without requiring any external power source.
They are capable of handling large loads during start-up as well as smaller loads in continuous and modulating operation with a single orifice.
These floating float type traps are manufactured in stainless steel, available with soft seating, and can be used in combination with other air removal and separation systems or directly applied at high points in distribution pipelines.
- Suitable for start-up and continuous operation with a single orifice.
- Allow for quick and easy in-line maintenance.
- Corrosion resistant internal parts.
- No balancing tube required.
- Cold, hot and superheated water or other liquids compatible with the construction.
- AE41.2-6, 14, 21 and 32 - stainless steel.
- 1" x 1/2"; DN 25 x 15.
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Socket weld (SW) ASME 16.11.
MAX. AP:
- AE41.2-6 – 6 bar
- AE41.2-14 – 14 bar
- AE41.2-21 – 21 bar
- AE41.2-32 – 32 bar
- Vertical installation.
- It must be installed absolutely vertically at the points in the plant where the air tends to collect.
- See IMI – Installation and maintenance instructions.
Automatic air and gas vents for liquid systems AE45.2 (Stainless steel 1” x 1/2”, 1” x 1”; DN 25 x 15, DN 25 x 25)
The AE45.2 range of automatic deaerators are designed to remove air or gases from water and other liquid systems, without requiring any external power source.
They are capable of handling large loads during start-up as well as smaller loads in continuous, modulating operation with a single orifice.
These floating float type traps are manufactured in stainless steel, available with soft seating, and can be used in combination with other air removal and separation systems or directly applied at high points in distribution pipelines
- Suitable for start-up and continuous operation with a single orifice.
- Allow for quick and easy in-line maintenance.
- Corrosion resistant internal parts.
- No balancing tube required.
- Metal to metal sealing.
- Threaded connection in the cover, closed with plug.
- HVV - Manual vent valve.
- Cold, hot and superheated water or other liquids compatible with the construction.
- AE45.2-6, 14, 21 and 32 - stainless steel.
- 1" x 1/2" and 1" x 1"; DN 25 x 15 and DN 25 x 25.
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Socket weld (SW) ASME 16.11.
- Vertical installation
MAX.AP:
- AE45.2-6 – 6 bar
- AE45.2-14 – 14 bar
- AE45.2-21 – 21 bar
- AE45.2-32 – 32 bar
Automatic air and gas vents for liquid systems AE47.2 (Stainless steel 11/2” x 1”, 2” x 1”, DN 40 x DN 25 and DN 50 x DN 25)
The AE47.2 range of automatic deaerators are designed to remove air or gases from water and other liquid systems, without requiring any external power source.
They are capable of handling large loads during start-up as well as smaller loads in continuous, modulating operation with a single orifice.
These floating float type traps are manufactured in stainless steel, available with soft seating, and can be used in combination with other air removal and separation systems or directly applied at high points in distribution piping.
- Suitable for start-up and continuous operation with a single orifice.
- Allow for quick and easy in-line maintenance.
- Corrosion resistant internal parts.
- No balancing tube required.
- Cold, hot and superheated water or other liquids compatible with the construction.
- AE47.2-10, 20 and 32 - stainless steel.
- 11/2" x 1" and 2" x 1"; DN 40 x DN 25 and DN 50 x DN 25.
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Socket weld (SW) ASME 16.11.
- Vertical in-line installation.
- Must be installed absolutely vertical at installation points where air tends to accumulate.
- See IMI - Installation and Maintenance Instructions
MAX.AP:
- AE47.2-10 – 10 bar
- AE47.2-20 – 20 bar
- AE47.2-32 – 32 bar
Automatic air and gas vents for liquid systems AE49.2 (Stainless steel 21/2” x 11/2”, 3” x 11/2”, DN 65 x DN 40 and DN 80 x DN 40)
The AE49.2 range of automatic deaerators are designed to remove air or gases from water and other liquid systems, without requiring any external power source.
They are capable of handling large loads during start-up as well as smaller loads in continuous, modulating operation with a single orifice.
These floating float type traps are manufactured in stainless steel, available with soft seating, and can be used in combination with other air removal and separation systems or directly applied at high points in distribution piping.
- Suitable for start-up and continuous operation with a single orifice.
- Allow for quick and easy in-line maintenance.
- Corrosion resistant internal parts.
- No balancing tube required
- Various soft sealing options.
- Cold, hot and superheated water or other liquids compatible with construction.
- AE49.2-5, 10, 20, 20, 28 and 32 - stainless steel.
- 21/2" x 11/2" and 3" x 11/2"; DN 65 x DN 40 and DN 80 x DN 40
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Socket weld (SW) ASME 16.11.
- Vertical in-line installation.
- Must be installed absolutely vertical at installation points where air tends to accumulate.
- See IMI - Installation and Maintenance Instructions
MAX.AP:
- AE49.2-5 – 5 bar
- AE49.2-10 – 10 bar
- AE49.2-20 – 20 bar
- AE49.2-28 – 28 bar
- AE49.2-32 – 32 bar
Automatic air and gas vents for liquid systems AE50I (Stainless steel from 1/2" x 1/2" to 1" x 1/2"; DN 15 x 1/2" to DN 25 x 1/2")
The AE50i range of automatic steam traps are designed to remove air or gases from water and other liquid systems, without requiring any external power source.
They are capable of handling large loads during start-up as well as smaller loads in continuous and modulating operation with a single orifice.
These floating float type traps are manufactured in stainless steel, available with soft seating, and can be used in combination with other air removal and separation systems or directly applied at high points in distribution piping.
- Suitable for start-up and continuous operation with a single orifice.
- Allow for quick and easy in-line maintenance.
- Corrosion resistant internal parts.
- Cold, hot and superheated water or other liquids compatible with the construction.
- AE50i - stainless steel. wants balancing tube.
- Various soft sealing options.
- Metal to metal sealing.
- Cold, hot and superheated water or other liquids compatible with the construction.
- AE50i - stainless steel.
- 1/2" x 1/2", 3/4" x 1/2" and 1" x 1/2";
- DN 15 x 1/2", DN 20 x 1/2" and DN 25 x 1/2".
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Vertical installation.
- It must be installed absolutely vertically at the points in the plant where the air tends to collect.
- The drain should be piped to a safe location.
- See IMI – Installation and maintenance instructions.
Automatic air and gas vens for liquid systems AE50S (Carbon steel from 1/2" x 1/2" to 1" x 1/2"; DN 15 x 1/2" to DN 25 x 1/2")
The AE50 range of automatic steam traps are designed to remove air or gases from water and other liquid systems without the need for any external power source.
They are capable of handling large loads during start-up, while being able to discharge smaller loads in continuous modulating operation with a single orifice.
These floating ball type traps are manufactured from carbon steel, are available with soft sealing and can be used in combination with other air removal and separation systems or applied directly at high points in pipelines.
- Suitable for start-up and continuous operation with a single orifice.
- Allow for quick and easy in-line maintenance.
- Corrosion resistant internal parts.
- No balancing pipework required.
- Different soft sealing options.
- Metal to metal sealing.
- Cold, hot and superheated water or other liquids compatible with the construction.
- AE50S - carbon steel.
- 1/2" x 1/2", 3/4" x 1/2" and 1" x 1/2";
- DN 15 x 1/2", DN 20 x 1/2" and DN 25 x 1/2".
- Female thread ISO 7 Rp or NPT.
- Flanged EN 1092-1 PN 40.
- Flanged ASME B16.5 Class 150 or 300.
- Vertical installation.
- It must be installed absolutely vertically at the points in the plant where the air tends to collect. The drain should be piped to a safe position.
- See IMI – Installation and maintenance instructions.